Remove default sizeof sizes in configure script when cross-compiling

[tools/e2fsprogs.git] / debugfs / debugfs.8.in

diff --git a/debugfs/debugfs.8.in b/debugfs/debugfs.8.in
index b640bf9..81b411e 100644 (file)
--- a/debugfs/debugfs.8.in
+++ b/debugfs/debugfs.8.in
@@ -335,18 +335,17 @@ device numbers must be specified.
 Take the requested list of inode numbers, and print a listing of pathnames
 to those inodes.
 .TP
-.I open [-w] [-f] [-i] [-c] [-b blocksize] [-s superblock] device
+.I open [-w] [-e] [-f] [-i] [-c] [-b blocksize] [-s superblock] device
 Open a filesystem for editing.  The 
-.I -w 
-flag causes the filesystem to be opened for writing.  The 
 .I -f 
 flag forces the filesystem to be opened even if there are some unknown 
 or incompatible filesystem features which would normally 
 prevent the filesystem from being opened.  The
-.IR -c ", " -b ", " -i ", " and " -s
-options behave the same as those to
-.B debugfs
-itself.
+.I -e
+flag causes the filesystem to be opened in exclusive mode.  The
+.IR -b ", " -c ", " -i ", " -s ", and " -w
+options behave the same as the command-line options to 
+.BR debugfs .
 .TP
 .I pwd
 Print the current working directory.
@@ -388,12 +387,20 @@ blocks starting at block number
 .I block
 will be marked as allocated.
 .TP
+.I set_block_group bgnum field value
+Modify the block group descriptor specified by
+.I bgnum
+so that the block group descriptor field
+.I field
+has value
+.I value.
+.TP
 .I seti filespec
 Mark inode 
 .I filespec
 as in use in the inode bitmap.
 .TP
-.I set_inode filespec field value
+.I set_inode_field filespec field value
 Modify the inode specified by 
 .I filespec
 so that the inode field
@@ -402,7 +409,7 @@ has value
 .I value.
 The list of valid inode fields which can be set via this command 
 can be displayed by using the command:
-.B set_inode -l
+.B set_inode_field -l
 .TP
 .I set_super_value field value
 Set the superblock field
@@ -439,6 +446,27 @@ Test if the inode
 .I filespec
 is marked as allocated in the inode bitmap.
 .TP
+.I undel <inode num> [pathname]
+Undelete the specified inode number (which must be surrounded by angle
+brackets) so that it and its blocks are marked in use, and optionally
+link the recovered inode to the specified pathname.  The 
+.B e2fsck
+command should always be run after using the 
+.B undel
+command to recover deleted files.
+.IP
+Note that if you are recovering a large number of deleted files, linking
+the inode to a directory may require the directory to be expanded, which
+could allocate a block that had been used by one of the
+yet-to-be-undeleted files.  So it is safer to undelete all of the 
+inodes without specifying a destination pathname, and then in a separate
+pass, use the debugfs
+.B link
+command to link the inode to the destination pathname, or use 
+.B e2fsck
+to check the filesystem and link all of the recovered inodes to the
+lost+found dirctory.
+.TP
 .I unlink pathname
 Remove the link specified by 
 .I pathname 
@@ -485,5 +513,6 @@ environment variable.
 was written by Theodore Ts'o <tytso@mit.edu>.
 .SH SEE ALSO
 .BR dumpe2fs (8),
+.BR tune2fs (8),
 .BR e2fsck (8),
 .BR mke2fs (8)