LU-8955 nodemap: add SELinux policy info to nodemap

[fs/lustre-release.git] / lustre / utils / lctl.c

diff --git a/lustre/utils/lctl.c b/lustre/utils/lctl.c
index c9632b9..4ed25e8 100644 (file)
--- a/lustre/utils/lctl.c
+++ b/lustre/utils/lctl.c
@@ -94,7 +94,7 @@ command_t cmdlist[] = {
         "usage: which_nid NID [NID...]"},
        {"replace_nids", jt_replace_nids, 0,
         "replace primary NIDs for a device\n"
-        "usage: replace_nids <device> <nid1>[,nid2,nid3]"},
+        "usage: replace_nids <device> <nid1>[,nid2,nid3:nid4,nid5:nid6]"},
        {"interface_list", jt_ptl_print_interfaces, 0,
         "print network interface entries\n"
         "usage: interface_list"},
@@ -117,7 +117,8 @@ command_t cmdlist[] = {
         "                    <<-r | --rate DROP_RATE> |\n"
         "                    <-i | --interval SECONDS>>\n"
         "                    [<-p | --portal> PORTAL...]\n"
-        "                    [<-m | --message> <PUT|ACK|GET|REPLY>...]\n"},
+        "                    [<-m | --message> <PUT|ACK|GET|REPLY>...]\n"
+        "                    [< -e | --health_error]\n"},
        {"net_drop_del", jt_ptl_drop_del, 0, "remove LNet drop rule\n"
         "usage: net_drop_del <[-a | --all] |\n"
         "                    <-s | --source NID>\n"
@@ -163,7 +164,8 @@ command_t cmdlist[] = {
        {"set_timeout", jt_lcfg_set_timeout, 0,
         "usage: conf_param obd_timeout=<secs>\n"},
 #if LUSTRE_VERSION_CODE < OBD_OCD_VERSION(3, 0, 53, 0)
-       {"conf_param", jt_lcfg_mgsparam, 0,"set a permanent config parameter.\n"
+       {"conf_param", jt_lcfg_confparam, 0,
+        "set a permanent config parameter.\n"
         "This command must be run on the MGS node\n"
         "usage: conf_param [-d] <target.keyword=val>\n"
         "  -d  Delete the permanent setting from the configuration."},
@@ -181,12 +183,13 @@ command_t cmdlist[] = {
         "      (Especially useful when using patterns.)\n"
         "  -R  Get parameters recursively from the specified entry.\n"},
        {"set_param", jt_lcfg_setparam, 0, "set the Lustre or LNET parameter\n"
-        "usage: set_param [-n] [-P] [-d]"
+        "usage: set_param [-n] [-P] [-d] [-F]"
         "<param_path1=value1 param_path2=value2 ...>\n"
         "Set the value of the Lustre or LNET parameter at the specified path.\n"
         "  -n  Disable printing of the key name when printing values.\n"
         "  -P  Set the parameter permanently, filesystem-wide.\n"
-        "  -d  Remove the permanent setting (only with -P option).\n"},
+        "  -d  Remove the permanent setting (only with -P option).\n"
+        "  -F  Read permanent configuration from a YAML file.\n"},
        {"list_param", jt_lcfg_listparam, 0,
         "list the Lustre or LNET parameter name\n"
         "usage: list_param [-F|-R|-D] <param_path1 param_path2 ...>\n"
@@ -327,6 +330,9 @@ command_t cmdlist[] = {
        {"nodemap_set_fileset", jt_nodemap_set_fileset, 0,
         "set a fileset on a nodemap\n"
         "usage: nodemap_set_fileset <fileset>"},
+       {"nodemap_set_sepol", jt_nodemap_set_sepol, 0,
+        "set SELinux policy info on a nodemap\n"
+        "usage: nodemap_set_sepol <SELinux policy info>"},
        {"nodemap_test_nid", jt_nodemap_test_nid, 0,
         "usage: nodemap_test_nid <nid>"},
        {"nodemap_test_id", jt_nodemap_test_id, 0,