#!/bin/bash
-# requirement:
-# add uml1 uml2 uml3 in your /etc/hosts
+# -*- mode: Bash; tab-width: 4; indent-tabs-mode: t; -*-
+# vim:autoindent:shiftwidth=4:tabstop=4:
# FIXME - there is no reason to use all of these different
# return codes, espcially when most of them are mapped to something
ONLY=${ONLY:-"$*"}
# bug number for skipped test:
-ALWAYS_EXCEPT=" $CONF_SANITY_EXCEPT"
+# 15977
+ALWAYS_EXCEPT="$CONF_SANITY_EXCEPT"
# UPDATE THE COMMENT ABOVE WITH BUG NUMBERS WHEN CHANGING ALWAYS_EXCEPT!
+if [ "$FAILURE_MODE" = "HARD" ]; then
+ CONFIG_EXCEPTIONS="24a " && \
+ echo "Except the tests: $CONFIG_EXCEPTIONS for FAILURE_MODE=$FAILURE_MODE, bug 23573" && \
+ ALWAYS_EXCEPT="$ALWAYS_EXCEPT $CONFIG_EXCEPTIONS"
+fi
+
SRCDIR=`dirname $0`
PATH=$PWD/$SRCDIR:$SRCDIR:$SRCDIR/../utils:$PATH
. $LUSTRE/tests/test-framework.sh
init_test_env $@
+
+# use small MDS + OST size to speed formatting time
+# do not use too small MDSSIZE/OSTSIZE, which affect the default jouranl size
+MDSSIZE=200000
+OSTSIZE=200000
+. ${CONFIG:=$LUSTRE/tests/cfg/$NAME.sh}
+
+if ! combined_mgs_mds; then
+ # bug number for skipped test: 23954
+ ALWAYS_EXCEPT="$ALWAYS_EXCEPT 24b"
+fi
+
# STORED_MDSSIZE is used in test_18
if [ -n "$MDSSIZE" ]; then
STORED_MDSSIZE=$MDSSIZE
fi
-# use small MDS + OST size to speed formatting time
-MDSSIZE=40000
-OSTSIZE=40000
-. ${CONFIG:=$LUSTRE/tests/cfg/$NAME.sh}
-remote_mds_nodsh && skip "remote MDS with nodsh" && exit 0
-remote_ost_nodsh && skip "remote OST with nodsh" && exit 0
+init_logging
#
-[ "$SLOW" = "no" ] && EXCEPT_SLOW="0 1 2 3 6 7 15 18 24b 25 30 31 32 33 34a 45"
+require_dsh_mds || exit 0
+require_dsh_ost || exit 0
+#
+[ "$SLOW" = "no" ] && EXCEPT_SLOW="30a 31 45"
+
assert_DIR
formatall
}
-writeconf() {
- local facet=$SINGLEMDS
- local dev=${facet}_dev
- shift
+writeconf1() {
+ local facet=$1
+ local dev=$2
+
stop ${facet} -f
rm -f ${facet}active
# who knows if/where $TUNEFS is installed? Better reformat if it fails...
- do_facet ${facet} "$TUNEFS --writeconf ${!dev}" || echo "tunefs failed, reformatting instead" && reformat
+ do_facet ${facet} "$TUNEFS --quiet --writeconf $dev" ||
+ { echo "tunefs failed, reformatting instead" && reformat_and_config && return 1; }
+ return 0
+}
- gen_config
+writeconf() {
+ # we need ldiskfs
+ load_modules
+ # if writeconf fails anywhere, we reformat everything
+ writeconf1 mds `mdsdevname 1` || return 0
+ writeconf1 ost1 `ostdevname 1` || return 0
+ writeconf1 ost2 `ostdevname 2` || return 0
}
gen_config() {
reformat_and_config() {
reformat
+ if ! combined_mgs_mds ; then
+ start_mgs
+ fi
gen_config
}
+start_mgs () {
+ echo "start mgs"
+ start mgs $MGSDEV $MGS_MOUNT_OPTS
+}
+
start_mds() {
local facet=$SINGLEMDS
# we can not use MDSDEV1 here because SINGLEMDS could be set not to mds1 only
local num=$(echo $facet | tr -d "mds")
local dev=$(mdsdevname $num)
echo "start mds service on `facet_active_host $facet`"
- start $facet ${dev} $MDS_MOUNT_OPTS || return 94
+ start $facet ${dev} $MDS_MOUNT_OPTS $@ || return 94
+}
+
+start_mgsmds() {
+ if ! combined_mgs_mds ; then
+ start_mgs
+ fi
+ start_mds $@
}
stop_mds() {
stop $SINGLEMDS -f || return 97
}
+stop_mgs() {
+ echo "stop mgs service on `facet_active_host mgs`"
+ # These tests all use non-failover stop
+ stop mgs -f || return 97
+}
+
start_ost() {
echo "start ost1 service on `facet_active_host ost1`"
- start ost1 `ostdevname 1` $OST_MOUNT_OPTS || return 95
+ start ost1 `ostdevname 1` $OST_MOUNT_OPTS $@ || return 95
}
stop_ost() {
start_ost2() {
echo "start ost2 service on `facet_active_host ost2`"
- start ost2 `ostdevname 2` $OST_MOUNT_OPTS || return 92
+ start ost2 `ostdevname 2` $OST_MOUNT_OPTS $@ || return 92
}
stop_ost2() {
}
setup() {
- start_ost
- start_mds
- mount_client $MOUNT
+ start_mds || error "MDT start failed"
+ start_ost || error "OST start failed"
+ mount_client $MOUNT || error "client start failed"
}
setup_noconfig() {
+ if ! combined_mgs_mds ; then
+ start_mgs
+ fi
+
start_mds
start_ost
mount_client $MOUNT
}
+unload_modules_conf () {
+ if combined_mgs_mds || ! local_mode; then
+ unload_modules || return 1
+ fi
+}
+
cleanup_nocli() {
- stop_mds || return 201
stop_ost || return 202
- unload_modules || return 203
+ stop_mds || return 201
+ unload_modules_conf || return 203
}
cleanup() {
run_test 0 "single mount setup"
test_1() {
+ start_mds || error "MDT start failed"
start_ost
echo "start ost second time..."
- setup
+ start_ost && error "2nd OST start should fail"
+ mount_client $MOUNT || error "client start failed"
check_mount || return 42
cleanup || return $?
}
run_test 1 "start up ost twice (should return errors)"
test_2() {
- start_ost
start_mds
echo "start mds second time.."
- start_mds
+ start_mds && error "2nd MDT start should fail"
+ start_ost
mount_client $MOUNT
check_mount || return 43
cleanup || return $?
test_3() {
setup
#mount.lustre returns an error if already in mtab
- mount_client $MOUNT && return $?
+ mount_client $MOUNT && error "2nd client mount should fail"
check_mount || return 44
cleanup || return $?
}
}
run_test 5a "force cleanup mds, then cleanup"
+cleanup_5b () {
+ trap 0
+ start_mgs
+}
+
test_5b() {
+ grep " $MOUNT " /etc/mtab && \
+ error false "unexpected entry in mtab before mount" && return 10
+
+ local rc=0
start_ost
+ if ! combined_mgs_mds ; then
+ trap cleanup_5b EXIT ERR
+ start_mds
+ stop mgs
+ fi
+
[ -d $MOUNT ] || mkdir -p $MOUNT
- grep " $MOUNT " /etc/mtab && echo "test 5b: mtab before mount" && return 10
- mount_client $MOUNT && return 1
- grep " $MOUNT " /etc/mtab && echo "test 5b: mtab after failed mount" && return 11
+ mount_client $MOUNT && rc=1
+ grep " $MOUNT " /etc/mtab && \
+ error "$MOUNT entry in mtab after failed mount" && rc=11
umount_client $MOUNT
# stop_mds is a no-op here, and should not fail
- cleanup_nocli || return $?
- return 0
+ cleanup_nocli || rc=$?
+ if ! combined_mgs_mds ; then
+ cleanup_5b
+ fi
+ return $rc
}
-run_test 5b "mds down, cleanup after failed mount (bug 2712) (should return errs)"
+run_test 5b "Try to start a client with no MGS (should return errs)"
test_5c() {
- start_ost
+ grep " $MOUNT " /etc/mtab && \
+ error false "unexpected entry in mtab before mount" && return 10
+
+ local rc=0
start_mds
+ start_ost
[ -d $MOUNT ] || mkdir -p $MOUNT
- grep " $MOUNT " /etc/mtab && echo "test 5c: mtab before mount" && return 10
local oldfs="${FSNAME}"
FSNAME="wrong.${FSNAME}"
mount_client $MOUNT || :
FSNAME=${oldfs}
- grep " $MOUNT " /etc/mtab && echo "test 5c: mtab after failed mount" && return 11
+ grep " $MOUNT " /etc/mtab && \
+ error "$MOUNT entry in mtab after failed mount" && rc=11
umount_client $MOUNT
- cleanup_nocli || return $?
+ cleanup_nocli || rc=$?
+ return $rc
}
run_test 5c "cleanup after failed mount (bug 2712) (should return errs)"
test_5d() {
+ grep " $MOUNT " /etc/mtab && \
+ error false "unexpected entry in mtab before mount" && return 10
+
+ local rc=0
start_ost
start_mds
stop_ost -f
- grep " $MOUNT " /etc/mtab && echo "test 5d: mtab before mount" && return 10
- mount_client $MOUNT || return 1
- cleanup || return $?
- grep " $MOUNT " /etc/mtab && echo "test 5d: mtab after unmount" && return 11
- return 0
+ mount_client $MOUNT || rc=1
+ cleanup || rc=$?
+ grep " $MOUNT " /etc/mtab && \
+ error "$MOUNT entry in mtab after unmount" && rc=11
+ return $rc
}
run_test 5d "mount with ost down"
test_5e() {
- start_ost
+ grep " $MOUNT " /etc/mtab && \
+ error false "unexpected entry in mtab before mount" && return 10
+
+ local rc=0
start_mds
+ start_ost
#define OBD_FAIL_PTLRPC_DELAY_SEND 0x506
do_facet client "lctl set_param fail_loc=0x80000506"
- grep " $MOUNT " /etc/mtab && echo "test 5e: mtab before mount" && return 10
mount_client $MOUNT || echo "mount failed (not fatal)"
- cleanup || return $?
- grep " $MOUNT " /etc/mtab && echo "test 5e: mtab after unmount" && return 11
- return 0
+ cleanup || rc=$?
+ grep " $MOUNT " /etc/mtab && \
+ error "$MOUNT entry in mtab after unmount" && rc=11
+ return $rc
}
run_test 5e "delayed connect, don't crash (bug 10268)"
+test_5f() {
+ if combined_mgs_mds ; then
+ skip "combined mgs and mds"
+ return 0
+ fi
+
+ grep " $MOUNT " /etc/mtab && \
+ error false "unexpected entry in mtab before mount" && return 10
+
+ local rc=0
+ start_ost
+ [ -d $MOUNT ] || mkdir -p $MOUNT
+ mount_client $MOUNT &
+ local pid=$!
+ echo client_mount pid is $pid
+
+ sleep 5
+
+ if ! ps -f -p $pid >/dev/null; then
+ wait $pid
+ rc=$?
+ grep " $MOUNT " /etc/mtab && echo "test 5f: mtab after mount"
+ error "mount returns $rc, expected to hang"
+ rc=11
+ cleanup || rc=$?
+ return $rc
+ fi
+
+ # start mds
+ start_mds
+
+ # mount should succeed after start mds
+ wait $pid
+ rc=$?
+ [ $rc -eq 0 ] || error "mount returned $rc"
+ grep " $MOUNT " /etc/mtab && echo "test 5f: mtab after mount"
+ cleanup || return $?
+ return $rc
+}
+run_test 5f "mds down, cleanup after failed mount (bug 2712)"
+
test_6() {
setup
manual_umount_client
fi
stop_ost || return $?
}
-
run_test 9 "test ptldebug and subsystem for mkfs"
-# LOGS/PENDING do not exist anymore since CMD3
-test_16() {
- local TMPMTPT="${TMP}/conf16"
- local dev=${SINGLEMDS}_dev
- local MDSDEV=${!dev}
- if [ ! -e "$MDSDEV" ]; then
- log "no $MDSDEV existing, so mount Lustre to create one"
- setup
- check_mount || return 41
- cleanup || return $?
- fi
+is_blkdev () {
+ local facet=$1
+ local dev=$2
+ local size=${3:-""}
- [ -f "$MDSDEV" ] && LOOPOPT="-o loop"
+ local rc=0
+ do_facet $facet "test -b $dev" || rc=1
+ if [[ "$size" ]]; then
+ local in=$(do_facet $facet "dd if=$dev of=/dev/null bs=1k count=1 skip=$size 2>&1" |\
+ awk '($3 == "in") { print $1 }')
+ [[ $in = "1+0" ]] || rc=1
+ fi
+ return $rc
+}
- log "change the mode of $MDSDEV/OBJECTS to 555"
- do_facet $SINGLEMDS "mkdir -p $TMPMTPT &&
- mount $LOOPOPT -t $FSTYPE $MDSDEV $TMPMTPT &&
- chmod 555 $TMPMTPT/OBJECTS &&
- umount $TMPMTPT" || return $?
+#
+# Test 16 was to "verify that lustre will correct the mode of OBJECTS".
+# But with new MDS stack we don't care about the mode of local objects
+# anymore, so this test is removed. See bug 22944 for more details.
+#
- log "mount Lustre to change the mode of OBJECTS, then umount Lustre"
- setup
+test_17() {
+ setup
check_mount || return 41
cleanup || return $?
- log "read the mode of OBJECTS and check if they has been changed properly"
- EXPECTEDOBJECTSMODE=`do_facet $SINGLEMDS "$DEBUGFS -R 'stat OBJECTS' $MDSDEV 2> /dev/null" | grep 'Mode: ' | sed -e "s/.*Mode: *//" -e "s/ *Flags:.*//"`
-
- if [ "$EXPECTEDOBJECTSMODE" = "0777" ]; then
- log "Success:Lustre change the mode of OBJECTS correctly"
- else
- error "Lustre does not change mode of OBJECTS properly"
+ echo "Remove mds config log"
+ if ! combined_mgs_mds ; then
+ stop mgs
fi
-}
-run_test 16 "verify that lustre will correct the mode of OBJECTS"
-test_17() {
- local dev=${SINGLEMDS}_dev
- local MDSDEV=${!dev}
-
- if [ ! -e "$MDSDEV" ]; then
- echo "no $MDSDEV existing, so mount Lustre to create one"
- setup
- check_mount || return 41
- cleanup || return $?
- fi
+ do_facet mgs "$DEBUGFS -w -R 'unlink CONFIGS/$FSNAME-MDT0000' $MGSDEV || return \$?" || return $?
- echo "Remove mds config log"
- do_facet $SINGLEMDS "$DEBUGFS -w -R 'unlink CONFIGS/$FSNAME-MDT0000' $MDSDEV || return \$?" || return $?
+ if ! combined_mgs_mds ; then
+ start_mgs
+ fi
start_ost
- start_mds && return 42
- reformat_and_config
+ start_mds && return 42
+ reformat_and_config
}
run_test 17 "Verify failed mds_postsetup won't fail assertion (2936) (should return errs)"
test_18() {
[ "$FSTYPE" != "ldiskfs" ] && skip "not needed for FSTYPE=$FSTYPE" && return
- local dev=${SINGLEMDS}_dev
- local MDSDEV=${!dev}
+ local MDSDEV=$(mdsdevname ${SINGLEMDS//mds/})
local MIN=2000000
log "use STORED_MDSSIZE=$STORED_MDSSIZE"
# check if the block device is large enough
- [ -z "$OK" -a -b $MDSDEV ] && \
- [ "$(dd if=$MDSDEV of=/dev/null bs=1k count=1 skip=$MIN 2>&1 |
- awk '($3 == "in") { print $1 }')" = "1+0" ] && OK=1 && \
+ [ -z "$OK" ] && $(is_blkdev $SINGLEMDS $MDSDEV $MIN) && OK=1 &&
myMDSSIZE=$MIN && log "use device $MDSDEV with MIN=$MIN"
# check if a loopback device has enough space for fs metadata (5%)
- [ -z "$OK" ] && [ -f $MDSDEV -o ! -e $MDSDEV ] &&
- SPACE=$(df -P $(dirname $MDSDEV) |
- awk '($1 != "Filesystem") {print $4}') &&
- [ $SPACE -gt $((MIN / 20)) ] && OK=1 && myMDSSIZE=$MIN && \
+
+ if [ -z "$OK" ]; then
+ local SPACE=$(do_facet $SINGLEMDS "[ -f $MDSDEV -o ! -e $MDSDEV ] && df -P \\\$(dirname $MDSDEV)" |
+ awk '($1 != "Filesystem") {print $4}')
+ ! [ -z "$SPACE" ] && [ $SPACE -gt $((MIN / 20)) ] && \
+ OK=1 && myMDSSIZE=$MIN && \
log "use file $MDSDEV with MIN=$MIN"
+ fi
[ -z "$OK" ] && skip_env "$MDSDEV too small for ${MIN}kB MDS" && return
echo "mount mds with large journal..."
local OLD_MDS_MKFS_OPTS=$MDS_MKFS_OPTS
- MDS_MKFS_OPTS="--mgs --mdt --fsname=$FSNAME --device-size=$myMDSSIZE --param sys.timeout=$TIMEOUT $MDSOPT"
+ local opts="--mdt --fsname=$FSNAME --device-size=$myMDSSIZE --param sys.timeout=$TIMEOUT $MDSOPT"
+
+ if combined_mgs_mds ; then
+ MDS_MKFS_OPTS="--mgs $opts"
+ else
+ MDS_MKFS_OPTS="--mgsnode=$MGSNID $opts"
+ fi
reformat_and_config
echo "mount lustre system..."
- setup
+ setup
check_mount || return 41
echo "check journal size..."
- local FOUNDSIZE=`do_facet mds "$DEBUGFS -c -R 'stat <8>' $MDSDEV" | awk '/Size: / { print $NF; exit;}'`
+ local FOUNDSIZE=$(do_facet $SINGLEMDS "$DEBUGFS -c -R 'stat <8>' $MDSDEV" | awk '/Size: / { print $NF; exit;}')
if [ $FOUNDSIZE -gt $((32 * 1024 * 1024)) ]; then
log "Success: mkfs creates large journals. Size: $((FOUNDSIZE >> 20))M"
else
test_20() {
# first format the ost/mdt
- start_ost
start_mds
+ start_ost
mount_client $MOUNT
check_mount || return 43
rm -f $DIR/$tfile
}
run_test 21c "start mds between two osts, stop mds last"
+test_21d() {
+ if combined_mgs_mds ; then
+ skip "need separate mgs device" && return 0
+ fi
+ stopall
+
+ reformat
+
+ start_mgs
+ start_ost
+ start_ost2
+ start_mds
+ wait_osc_import_state mds ost2 FULL
+
+ stop_ost
+ stop_ost2
+ stop_mds
+ stop_mgs
+}
+run_test 21d "start mgs then ost and then mds"
+
test_22() {
start_mds
run_test 22 "start a client before osts (should return errs)"
test_23a() { # was test_23
- setup
- # fail mds
+ setup
+ # fail mds
stop $SINGLEMDS
# force down client so that recovering mds waits for reconnect
local running=$(grep -c $MOUNT /proc/mounts) || true
local PID1
local PID2
local WAIT=0
- local MAX_WAIT=20
+ local MAX_WAIT=30
local sleep=1
while [ "$WAIT" -lt "$MAX_WAIT" ]; do
sleep $sleep
echo "waiting for mount to finish ... "
WAIT=$(( WAIT + sleep))
done
- [ "$WAIT" -eq "$MAX_WAIT" ] && error "MOUNT_PID $MOUNT_PID and \
- MOUNT__LUSTRE_PID $MOUNT__LUSTRE_PID still not killed in $WAIT secs"
- ps -ef | grep mount
+ if [ "$WAIT" -eq "$MAX_WAIT" ]; then
+ error "MOUNT_PID $MOUNT_PID and "\
+ "MOUNT_LUSTRE_PID $MOUNT_LUSTRE_PID still not killed in $WAIT secs"
+ ps -ef | grep mount
+ fi
stop_mds || error
stop_ost || error
}
cleanup_nocli
test_23b() { # was test_23
- start_ost
start_mds
+ start_ost
# Simulate -EINTR during mount OBD_FAIL_LDLM_CLOSE_THREAD
lctl set_param fail_loc=0x80000313
mount_client $MOUNT
}
test_24a() {
- #set up fs1
- gen_config
- #set up fs2
- [ -n "$ost1_HOST" ] && fs2ost_HOST=$ost1_HOST
+ local MDSDEV=$(mdsdevname ${SINGLEMDS//mds/})
+
if [ -z "$fs2ost_DEV" -o -z "$fs2mds_DEV" ]; then
- do_facet $SINGLEMDS [ -b "$MDSDEV" ] && \
+ is_blkdev $SINGLEMDS $MDSDEV && \
skip_env "mixed loopback and real device not working" && return
fi
+ [ -n "$ost1_HOST" ] && fs2ost_HOST=$ost1_HOST
+
local fs2mdsdev=${fs2mds_DEV:-${MDSDEV}_2}
local fs2ostdev=${fs2ost_DEV:-$(ostdevname 1)_2}
run_test 24a "Multiple MDTs on a single node"
test_24b() {
+ local MDSDEV=$(mdsdevname ${SINGLEMDS//mds/})
+
if [ -z "$fs2mds_DEV" ]; then
- do_facet $SINGLEMDS [ -b "$MDSDEV" ] && \
+ local dev=${SINGLEMDS}_dev
+ local MDSDEV=${!dev}
+ is_blkdev $SINGLEMDS $MDSDEV && \
skip_env "mixed loopback and real device not working" && return
fi
do_facet $SINGLEMDS "lctl set_param fail_loc=0x80000135"
start_mds && echo MDS started && return 1
lctl get_param -n devices
- DEVS=$(lctl get_param -n devices | wc -l)
+ DEVS=$(lctl get_param -n devices | egrep -v MG | wc -l)
[ $DEVS -gt 0 ] && return 2
- unload_modules || return 203
+ unload_modules_conf || return $?
}
run_test 26 "MDT startup failure cleans LOV (should return errs)"
fi
# check MDT too
- local MPROC="osc.$FSNAME-OST0001-osc-[M]*.active"
+ local mdtosc=$(get_mdtosc_proc_path $SINGLEMDS $FSNAME-OST0001)
+ mdtosc=${mdtosc/-MDT*/-MDT\*}
+ local MPROC="osc.$mdtosc.active"
local MAX=30
local WAIT=0
while [ 1 ]; do
}
run_test 29 "permanently remove an OST"
-test_30() {
+test_30a() {
setup
+ echo Big config llog
TEST="lctl get_param -n llite.$FSNAME-*.max_read_ahead_whole_mb"
ORIG=$($TEST)
LIST=(1 2 3 4 5 4 3 2 1 2 3 4 5 4 3 2 1 2 3 4 5)
# make sure client restart still works
umount_client $MOUNT
mount_client $MOUNT || return 4
- [ "$($TEST)" -ne "$i" ] && return 5
- set_and_check client "$TEST" "$FSNAME.llite.max_read_ahead_whole_mb" $ORIG || return 6
+ [ "$($TEST)" -ne "$i" ] && error "Param didn't stick across restart $($TEST) != $i"
+ pass
+
+ echo Erase parameter setting
+ do_facet mgs "$LCTL conf_param -d $FSNAME.llite.max_read_ahead_whole_mb" || return 6
+ umount_client $MOUNT
+ mount_client $MOUNT || return 6
+ FINAL=$($TEST)
+ echo "deleted (default) value=$FINAL, orig=$ORIG"
+ # assumes this parameter started at the default value
+ [ "$FINAL" -eq "$ORIG" ] || fail "Deleted value=$FINAL, orig=$ORIG"
+
+ cleanup
+}
+run_test 30a "Big config llog and conf_param deletion"
+
+test_30b() {
+ setup
+
+ # Make a fake nid. Use the OST nid, and add 20 to the least significant
+ # numerical part of it. Hopefully that's not already a failover address for
+ # the server.
+ OSTNID=$(do_facet ost1 "$LCTL get_param nis" | tail -1 | awk '{print $1}')
+ ORIGVAL=$(echo $OSTNID | egrep -oi "[0-9]*@")
+ NEWVAL=$((($(echo $ORIGVAL | egrep -oi "[0-9]*") + 20) % 256))
+ NEW=$(echo $OSTNID | sed "s/$ORIGVAL/$NEWVAL@/")
+ echo "Using fake nid $NEW"
+
+ TEST="$LCTL get_param -n osc.$FSNAME-OST0000-osc-[^M]*.import | grep failover_nids | sed -n 's/.*\($NEW\).*/\1/p'"
+ set_and_check client "$TEST" "$FSNAME-OST0000.failover.node" $NEW || error "didn't add failover nid $NEW"
+ NIDS=$($LCTL get_param -n osc.$FSNAME-OST0000-osc-[^M]*.import | grep failover_nids)
+ echo $NIDS
+ NIDCOUNT=$(($(echo "$NIDS" | wc -w) - 1))
+ echo "should have 2 failover nids: $NIDCOUNT"
+ [ $NIDCOUNT -eq 2 ] || error "Failover nid not added"
+ do_facet mgs "$LCTL conf_param -d $FSNAME-OST0000.failover.node" || error "conf_param delete failed"
+ umount_client $MOUNT
+ mount_client $MOUNT || return 3
+
+ NIDS=$($LCTL get_param -n osc.$FSNAME-OST0000-osc-[^M]*.import | grep failover_nids)
+ echo $NIDS
+ NIDCOUNT=$(($(echo "$NIDS" | wc -w) - 1))
+ echo "only 1 final nid should remain: $NIDCOUNT"
+ [ $NIDCOUNT -eq 1 ] || error "Failover nids not removed"
+
cleanup
}
-run_test 30 "Big config llog"
+run_test 30b "Remove failover nids"
test_31() { # bug 10734
# ipaddr must not exist
umount -f $MOUNT || true
echo "Cleanup local mds ost1 ..."
cleanup_nocli32
- unload_modules
+ combined_mgs_mds || start_mgs
+ unload_modules_conf
}
test_32a() {
$TUNEFS $tmpdir/mds || error "tunefs failed"
+ combined_mgs_mds || stop mgs
+
# nids are wrong, so client wont work, but server should start
start32 mds1 $tmpdir/mds "-o loop,exclude=lustre-OST0000" && \
trap cleanup_32 EXIT INT || return 3
# mount a second time to make sure we didnt leave upgrade flag on
load_modules
$TUNEFS --dryrun $tmpdir/mds || error "tunefs failed"
+
+ combined_mgs_mds || stop mgs
+
start32 mds1 $tmpdir/mds "-o loop,exclude=lustre-OST0000" && \
trap cleanup_32 EXIT INT || return 12
{ skip_env "Cannot untar $DISK1_8" && return ; }
load_modules
- $LCTL set_param debug=$PTLDEBUG
+ $LCTL set_param debug="config"
local NEWNAME=lustre
# writeconf will cause servers to register with their current nids
$TUNEFS --writeconf --fsname=$NEWNAME $tmpdir/mds || error "tunefs failed"
+ combined_mgs_mds || stop mgs
+
start32 mds1 $tmpdir/mds "-o loop" && \
trap cleanup_32 EXIT INT || return 3
echo MDS uuid $UUID
[ "$UUID" == "${NEWNAME}-MDT0000_UUID" ] || error "UUID is wrong: $UUID"
- $TUNEFS --mgsnode=$HOSTNAME --writeconf --fsname=$NEWNAME $tmpdir/ost1 || error "tunefs failed"
+ $TUNEFS --mgsnode=$HOSTNAME --writeconf --fsname=$NEWNAME $tmpdir/ost1 ||\
+ error "tunefs failed"
start32 ost1 $tmpdir/ost1 "-o loop" || return 5
UUID=$($LCTL get_param -n obdfilter.${NEWNAME}-OST0000.uuid)
echo OST uuid $UUID
echo "MDC changes should succeed:"
$LCTL conf_param ${NEWNAME}-MDT0000.mdc.max_rpcs_in_flight=9 || return 9
- $LCTL conf_param lustre-MDT0000.failover.node=$NID || return 10
+ $LCTL conf_param ${NEWNAME}-MDT0000.failover.node=$NID || return 10
echo "ok."
echo "LOV changes should succeed:"
- $LCTL pool_new lustre.interop || return 11
- $LCTL conf_param lustre-MDT0000.lov.stripesize=4M || return 12
+ $LCTL pool_new ${NEWNAME}.interop || return 11
+ $LCTL conf_param ${NEWNAME}-MDT0000.lov.stripesize=4M || return 12
echo "ok."
# MDT and OST should have registered with new nids, so we should have
test_33a() { # bug 12333, was test_33
local rc=0
local FSNAME2=test-123
+ local MDSDEV=$(mdsdevname ${SINGLEMDS//mds/})
+
[ -n "$ost1_HOST" ] && fs2ost_HOST=$ost1_HOST
if [ -z "$fs2ost_DEV" -o -z "$fs2mds_DEV" ]; then
- do_facet $SINGLEMDS [ -b "$MDSDEV" ] && \
+ local dev=${SINGLEMDS}_dev
+ local MDSDEV=${!dev}
+ is_blkdev $SINGLEMDS $MDSDEV && \
skip_env "mixed loopback and real device not working" && return
fi
+ combined_mgs_mds || mkfs_opts="$mkfs_opts --nomgs"
+
local fs2mdsdev=${fs2mds_DEV:-${MDSDEV}_2}
local fs2ostdev=${fs2ost_DEV:-$(ostdevname 1)_2}
add fs2mds $MDS_MKFS_OPTS --mkfsoptions='\"-J size=8\"' --fsname=${FSNAME2} --reformat $fs2mdsdev || exit 10
}" $TMP/lustre-log-$TESTNAME.log`
[ "$NEXTCONN" != "0" ] && log "The client didn't try to reconnect to the last active server (tried ${NEXTCONN} instead)" && return 7
cleanup
+ # remove nid settings
+ writeconf
}
run_test 35a "Reconnect to the last active server first"
log "Set up a fake failnode for the MDS"
FAKENID="127.0.0.2"
- local device=$(do_facet mds "$LCTL get_param -n devices" | \
+ local device=$(do_facet $SINGLEMDS "$LCTL get_param -n devices" | \
awk '($3 ~ "mdt" && $4 ~ "MDT") { print $4 }' | head -1)
- do_facet mds "$LCTL conf_param ${device}.failover.node=$FAKENID" || \
+ do_facet $SINGLEMDS "$LCTL conf_param ${device}.failover.node=$FAKENID" || \
return 1
local at_max_saved=0
log "Injecting EBUSY on MDS"
# Setting OBD_FAIL_MDS_RESEND=0x136
- do_facet mds "$LCTL set_param fail_loc=0x80000136" || return 2
+ do_facet $SINGLEMDS "$LCTL set_param fail_loc=0x80000136" || return 2
log "Stat on a test file"
stat $MOUNT/testdir/test
log "Stop injecting EBUSY on MDS"
- do_facet mds "$LCTL set_param fail_loc=0" || return 3
+ do_facet $SINGLEMDS "$LCTL set_param fail_loc=0" || return 3
rm -f $MOUNT/testdir/test
log "done"
return 5
cleanup
+ # remove nid settings
+ writeconf
}
run_test 35b "Continue reconnection retries, if the active server is busy"
test_36() { # 12743
- local rc
+ [ $OSTCOUNT -lt 2 ] && skip_env "skipping test for single OST" && return
+
+ [ "$ost_HOST" = "`hostname`" -o "$ost1_HOST" = "`hostname`" ] || \
+ { skip "remote OST" && return 0; }
+
+ local rc=0
local FSNAME2=test1234
local fs3ost_HOST=$ost_HOST
+ local MDSDEV=$(mdsdevname ${SINGLEMDS//mds/})
[ -n "$ost1_HOST" ] && fs2ost_HOST=$ost1_HOST && fs3ost_HOST=$ost1_HOST
- rc=0
if [ -z "$fs2ost_DEV" -o -z "$fs2mds_DEV" -o -z "$fs3ost_DEV" ]; then
- do_facet $SINGLEMDS [ -b "$MDSDEV" ] && \
+ is_blkdev $SINGLEMDS $MDSDEV && \
skip_env "mixed loopback and real device not working" && return
fi
- [ $OSTCOUNT -lt 2 ] && skip_env "skipping test for single OST" && return
-
- [ "$ost_HOST" = "`hostname`" -o "$ost1_HOST" = "`hostname`" ] || \
- { skip "remote OST" && return 0; }
local fs2mdsdev=${fs2mds_DEV:-${MDSDEV}_2}
local fs2ostdev=${fs2ost_DEV:-$(ostdevname 1)_2}
stop fs2ost -f || return 201
stop fs2mds -f || return 202
rm -rf $MOUNT2 $fs2mdsdev $fs2ostdev $fs3ostdev
- unload_modules || return 203
+ unload_modules_conf || return 203
return $rc
}
run_test 36 "df report consistency on OSTs with different block size"
test_37() {
- client_only && skip "client only testing" && return 0
- LOCAL_MDSDEV="$TMP/mdt.img"
- SYM_MDSDEV="$TMP/sym_mdt.img"
+ local mntpt=$(facet_mntpt $SINGLEMDS)
+ local mdsdev=$(mdsdevname ${SINGLEMDS//mds/})
+ local mdsdev_sym="$TMP/sym_mdt.img"
- echo "MDS : $LOCAL_MDSDEV"
- echo "SYMLINK : $SYM_MDSDEV"
- rm -f $LOCAL_MDSDEV
+ echo "MDS : $mdsdev"
+ echo "SYMLINK : $mdsdev_sym"
+ do_facet $SINGLEMDS rm -f $mdsdev_sym
- touch $LOCAL_MDSDEV
- mkfs.lustre --reformat --fsname=lustre --mdt --mgs --device-size=9000 $LOCAL_MDSDEV ||
- error "mkfs.lustre $LOCAL_MDSDEV failed"
- ln -s $LOCAL_MDSDEV $SYM_MDSDEV
+ do_facet $SINGLEMDS ln -s $mdsdev $mdsdev_sym
- echo "mount symlink device - $SYM_MDSDEV"
+ echo "mount symlink device - $mdsdev_sym"
- mount_op=`mount -v -t lustre -o loop $SYM_MDSDEV ${MOUNT%/*}/mds 2>&1 | grep "unable to set tunable"`
- umount -d ${MOUNT%/*}/mds
- rm -f $LOCAL_MDSDEV $SYM_MDSDEV
+ local rc=0
+ mount_op=$(do_facet $SINGLEMDS mount -v -t lustre $MDS_MOUNT_OPTS $mdsdev_sym $mntpt 2>&1 )
+ rc=${PIPESTATUS[0]}
- if [ -n "$mount_op" ]; then
- error "**** FAIL: set tunables failed for symlink device"
+ echo mount_op=$mount_op
+
+ do_facet $SINGLEMDS "umount -d $mntpt && rm -f $mdsdev_sym"
+
+ if $(echo $mount_op | grep -q "unable to set tunable"); then
+ error "set tunables failed for symlink device"
fi
+
+ [ $rc -eq 0 ] || error "mount symlink $mdsdev_sym failed! rc=$rc"
+
return 0
}
run_test 37 "verify set tunables works for symlink device"
log "rename lov_objid file on MDS"
rm -f $TMP/lov_objid.orig
- local dev=${SINGLEMDS}_dev
- local MDSDEV=${!dev}
+ local MDSDEV=$(mdsdevname ${SINGLEMDS//mds/})
do_facet $SINGLEMDS "$DEBUGFS -c -R \\\"dump lov_objid $TMP/lov_objid.orig\\\" $MDSDEV"
do_facet $SINGLEMDS "$DEBUGFS -w -R \\\"rm lov_objid\\\" $MDSDEV"
}
run_test 40 "race during service thread startup"
-test_41() { #bug 14134
+test_41a() { #bug 14134
+ echo $MDS_MOUNT_OPTS | grep "loop" && skip " loop devices does not work with nosvc option" && return
+
local rc
- local dev=${SINGLEMDS}_dev
- local MDSDEV=${!dev}
+ local MDSDEV=$(mdsdevname ${SINGLEMDS//mds/})
start $SINGLEMDS $MDSDEV $MDS_MOUNT_OPTS -o nosvc -n
start ost1 `ostdevname 1` $OST_MOUNT_OPTS
stop ost1 -f || return 201
stop_mds -f || return 202
stop_mds -f || return 203
- unload_modules || return 204
+ unload_modules_conf || return 204
return $rc
}
-run_test 41 "mount mds with --nosvc and --nomgs"
+run_test 41a "mount mds with --nosvc and --nomgs"
+
+test_41b() {
+ echo $MDS_MOUNT_OPTS | grep "loop" && skip " loop devices does not work with nosvc option" && return
+
+ stopall
+ reformat
+ local MDSDEV=$(mdsdevname ${SINGLEMDS//mds/})
+ start $SINGLEMDS $MDSDEV $MDS_MOUNT_OPTS -o nosvc -n
+ start_ost
+ start $SINGLEMDS $MDSDEV $MDS_MOUNT_OPTS -o nomgs,force
+ mkdir -p $MOUNT
+ mount_client $MOUNT || return 1
+ sleep 5
+
+ echo "blah blah" > $MOUNT/$tfile
+ cat $MOUNT/$tfile || return 200
+
+ umount_client $MOUNT
+ stop_ost || return 201
+ stop_mds -f || return 202
+ stop_mds -f || return 203
+
+}
+
+run_test 41b "mount mds with --nosvc and --nomgs on first mount"
test_42() { #bug 14693
setup
check_mount || return 2
- do_facet client lctl conf_param lustre.llite.some_wrong_param=10
+ do_facet mgs $LCTL conf_param lustre.llite.some_wrong_param=10
umount_client $MOUNT
mount_client $MOUNT || return 1
cleanup
check_mount || return 2
UUID=$($LCTL get_param llite.${FSNAME}*.uuid | cut -d= -f2)
STATS_FOUND=no
- UUIDS=$(do_facet mds "$LCTL get_param mdt.${FSNAME}*.exports.*.uuid")
+ UUIDS=$(do_facet $SINGLEMDS "$LCTL get_param mdt.${FSNAME}*.exports.*.uuid")
for VAL in $UUIDS; do
NID=$(echo $VAL | cut -d= -f1)
CLUUID=$(echo $VAL | cut -d= -f2)
let count=count-1
done
stop_mds || rc=$?
- # writeconf is needed after the test, otherwise,
- # we might end up with extra OSTs
- writeconf || rc=$?
cleanup_nocli || rc=$?
+ #writeconf to remove all ost2 traces for subsequent tests
+ writeconf
return $rc
}
test_46a() {
echo "Testing with $OSTCOUNT OSTs"
- reformat
+ reformat_and_config
start_mds || return 1
#first client should see only one ost
start_ost || return 2
facet_failover ost1
facet_failover $SINGLEMDS
- df -h $MOUNT || return 3
+ client_up || return 3
count=0
for ns in $($LCTL get_param ldlm.namespaces.$FSNAME-*-*-*.lru_size); do
OST_MKFS_OPTS="--ost --fsname=$FSNAME --device-size=$OSTSIZE --mgsnode=$MGSNID --param sys.timeout=$LOCAL_TIMEOUT --param sys.ldlm_timeout=$LOCAL_TIMEOUT $MKFSOPT $OSTOPT"
reformat
- start_mds
- start_ost
- mount_client $MOUNT
+ setup_noconfig
check_mount || return 1
echo "check ldlm_timout..."
- LDLM_MDS="`do_facet mds lctl get_param -n ldlm_timeout`"
+ LDLM_MDS="`do_facet $SINGLEMDS lctl get_param -n ldlm_timeout`"
LDLM_OST1="`do_facet ost1 lctl get_param -n ldlm_timeout`"
LDLM_CLIENT="`do_facet client lctl get_param -n ldlm_timeout`"
OST_MKFS_OPTS="--ost --fsname=$FSNAME --device-size=$OSTSIZE --mgsnode=$MGSNID --param sys.timeout=$LOCAL_TIMEOUT --param sys.ldlm_timeout=$((LOCAL_TIMEOUT - 1)) $MKFSOPT $OSTOPT"
reformat
- start_mds || return 4
- start_ost || return 5
- mount_client $MOUNT || return 6
+ setup_noconfig
check_mount || return 7
- LDLM_MDS="`do_facet mds lctl get_param -n ldlm_timeout`"
+ LDLM_MDS="`do_facet $SINGLEMDS lctl get_param -n ldlm_timeout`"
LDLM_OST1="`do_facet ost1 lctl get_param -n ldlm_timeout`"
LDLM_CLIENT="`do_facet client lctl get_param -n ldlm_timeout`"
umount_client $MOUNT || error "Unable to unmount client"
stop_ost || error "Unable to stop OST1"
stop_mds || error "Unable to stop MDS"
+ #writeconf to remove all ost2 traces for subsequent tests
writeconf
}
run_test 50f "normal statfs one server in down =========================="
[ "$OSTCOUNT" -lt "2" ] && skip_env "$OSTCOUNT < 2, skipping" && return
setup
start_ost2 || error "Unable to start OST2"
+ wait_osc_import_state mds ost2 FULL
+ wait_osc_import_state client ost2 FULL
local PARAM="${FSNAME}-OST0001.osc.active"
stop_ost2 || error "Unable to stop OST2"
stop_ost || error "Unable to stop OST1"
stop_mds || error "Unable to stop MDS"
+ #writeconf to remove all ost2 traces for subsequent tests
writeconf
}
run_test 50g "deactivated OST should not cause panic====================="
local LOCAL_TIMEOUT=20
reformat
- start_mds
- start_ost
- mount_client $MOUNT
+ setup_noconfig
check_mount || return 1
mkdir $MOUNT/d1
[ $? -eq 0 ] || { error "Unable to create tdir"; return 4; }
touch $TMP/modified_first
[ $? -eq 0 ] || { error "Unable to create temporary file"; return 5; }
- do_node $ost1node "mkdir -p $ost1tmp && touch $ost1tmp/modified_first"
+ local mtime=$(stat -c %Y $TMP/modified_first)
+ do_node $ost1node "mkdir -p $ost1tmp && touch -m -d @$mtime $ost1tmp/modified_first"
+
[ $? -eq 0 ] || { error "Unable to create temporary file"; return 6; }
sleep 1
}
run_test 52 "check recovering objects from lost+found"
+# Checks threads_min/max/started for some service
+#
+# Arguments: service name (OST or MDT), facet (e.g., ost1, $SINGLEMDS), and a
+# parameter pattern prefix like 'ost.*.ost'.
+thread_sanity() {
+ local modname=$1
+ local facet=$2
+ local parampat=$3
+ local opts=$4
+ local tmin
+ local tmin2
+ local tmax
+ local tmax2
+ local tstarted
+ local paramp
+ local msg="Insane $modname thread counts"
+ shift 4
+
+ setup
+ check_mount || return 41
+
+ # We need to expand $parampat, but it may match multiple parameters, so
+ # we'll pick the first one
+ if ! paramp=$(do_facet $facet "lctl get_param -N ${parampat}.threads_min"|head -1); then
+ error "Couldn't expand ${parampat}.threads_min parameter name"
+ return 22
+ fi
+
+ # Remove the .threads_min part
+ paramp=${paramp%.threads_min}
+
+ # Check for sanity in defaults
+ tmin=$(do_facet $facet "lctl get_param -n ${paramp}.threads_min" || echo 0)
+ tmax=$(do_facet $facet "lctl get_param -n ${paramp}.threads_max" || echo 0)
+ tstarted=$(do_facet $facet "lctl get_param -n ${paramp}.threads_started" || echo 0)
+ lassert 23 "$msg (PDSH problems?)" '(($tstarted && $tmin && $tmax))' || return $?
+ lassert 24 "$msg" '(($tstarted >= $tmin && $tstarted <= $tmax ))' || return $?
+
+ # Check that we can lower min/max
+ do_facet $facet "lctl set_param ${paramp}.threads_min=$((tmin - 1))"
+ do_facet $facet "lctl set_param ${paramp}.threads_max=$((tmax - 1))"
+ tmin2=$(do_facet $facet "lctl get_param -n ${paramp}.threads_min" || echo 0)
+ tmax2=$(do_facet $facet "lctl get_param -n ${paramp}.threads_max" || echo 0)
+ lassert 25 "$msg" '(($tmin2 == ($tmin - 1) && $tmax2 == ($tmax -1)))' || return $?
+
+ # Check that we can set min/max to the same value
+ do_facet $facet "lctl set_param ${paramp}.threads_max=$((tmin - 1))"
+ tmin2=$(do_facet $facet "lctl get_param -n ${paramp}.threads_min" || echo 0)
+ tmax2=$(do_facet $facet "lctl get_param -n ${paramp}.threads_max" || echo 0)
+ lassert 26 "$msg" '(($tmin2 == ($tmin - 1) && $tmax2 == ($tmin - 1)))' || return $?
+
+ # Check that we can't set max < min
+ do_facet $facet "lctl set_param ${paramp}.threads_max=$((tmin - 2))"
+ tmin2=$(do_facet $facet "lctl get_param -n ${paramp}.threads_min" || echo 0)
+ tmax2=$(do_facet $facet "lctl get_param -n ${paramp}.threads_max" || echo 0)
+ lassert 27 "$msg" '(($tmin2 <= $tmax2))' || return $?
+
+ # We need to ensure that we get the module options desired; to do this
+ # we set LOAD_MODULES_REMOTE=true and we call setmodopts below.
+ LOAD_MODULES_REMOTE=true
+ cleanup
+ local oldvalue
+ setmodopts -a $modname "$opts" oldvalue
+
+ load_modules
+ setup
+ check_mount || return 41
+
+ # Restore previous setting of MODOPTS_*
+ setmodopts $modname "$oldvalue"
+
+ # Check that $opts took
+ tmin=$(do_facet $facet "lctl get_param -n ${paramp}.threads_min")
+ tmax=$(do_facet $facet "lctl get_param -n ${paramp}.threads_max")
+ tstarted=$(do_facet $facet "lctl get_param -n ${paramp}.threads_started")
+ lassert 28 "$msg" '(($tstarted == $tmin && $tstarted == $tmax ))' || return $?
+ cleanup
+
+ # Workaround a YALA bug where YALA expects that modules will remain
+ # loaded on the servers
+ LOAD_MODULES_REMOTE=false
+ load_modules
+ setup
+ cleanup
+}
+
+test_53a() {
+ thread_sanity OST ost1 'ost.*.ost' 'oss_num_threads=64'
+}
+run_test 53a "check OSS thread count params"
+
+test_53b() {
+ thread_sanity MDT $SINGLEMDS 'mdt.*.*.' 'mdt_num_threads=64'
+}
+run_test 53b "check MDT thread count params"
+
+run_llverfs()
+{
+ local dir=$1
+ local partial_arg=""
+ local size=$(df -B G $dir | tail -1 | awk '{print $2}' | sed 's/G//') # Gb
+
+ # Run in partial (fast) mode if the size
+ # of a partition > 10 GB
+ [ $size -gt 10 ] && partial_arg="-p"
+
+ llverfs $partial_arg $dir
+}
+
+test_54a() {
+ do_rpc_nodes $(facet_host ost1) run_llverdev $(ostdevname 1)
+ [ $? -eq 0 ] || error "llverdev failed!"
+ reformat_and_config
+}
+run_test 54a "llverdev"
+
+test_54b() {
+ setup
+ run_llverfs $MOUNT
+ [ $? -eq 0 ] || error "llverfs failed!"
+ cleanup
+}
+run_test 54b "llverfs"
+
+lov_objid_size()
+{
+ local max_ost_index=$1
+ echo -n $(((max_ost_index + 1) * 8))
+}
+
+test_55() {
+ local mdsdev=$(mdsdevname 1)
+ local ostdev=$(ostdevname 1)
+ local saved_opts=$OST_MKFS_OPTS
+
+ for i in 0 1023 2048
+ do
+ OST_MKFS_OPTS="$saved_opts --index $i"
+ reformat
+
+ setup_noconfig
+ stopall
+
+ setup
+ sync
+ echo checking size of lov_objid for ost index $i
+ LOV_OBJID_SIZE=$(do_facet mds1 "$DEBUGFS -R 'stat lov_objid' $mdsdev 2>/dev/null" | grep ^User | awk '{print $6}')
+ if [ "$LOV_OBJID_SIZE" != $(lov_objid_size $i) ]; then
+ error "lov_objid size has to be $(lov_objid_size $i), not $LOV_OBJID_SIZE"
+ else
+ echo ok, lov_objid size is correct: $LOV_OBJID_SIZE
+ fi
+ stopall
+ done
+
+ OST_MKFS_OPTS=$saved_opts
+ reformat
+}
+run_test 55 "check lov_objid size"
+
+test_56() {
+ add mds1 $MDS_MKFS_OPTS --mkfsoptions='\"-J size=16\"' --reformat $(mdsdevname 1)
+ add ost1 $OST_MKFS_OPTS --index=1000 --reformat $(ostdevname 1)
+ add ost2 $OST_MKFS_OPTS --index=10000 --reformat $(ostdevname 2)
+
+ start_mds
+ start_ost
+ start_ost2 || error "Unable to start second ost"
+ mount_client $MOUNT || error "Unable to mount client"
+ echo ok
+ $LFS osts
+ [ -n "$ENABLE_QUOTA" ] && { $LFS quotacheck -ug $MOUNT || error "quotacheck has failed" ; }
+ stopall
+ reformat
+}
+run_test 56 "check big indexes"
+
+test_57() { # bug 22656
+ local NID=$(do_facet ost1 "$LCTL get_param nis" | tail -1 | awk '{print $1}')
+ writeconf
+ do_facet ost1 "$TUNEFS --failnode=$NID `ostdevname 1`" || error "tunefs failed"
+ start_mgsmds
+ start_ost && error "OST registration from failnode should fail"
+ stop_mds
+ reformat
+}
+run_test 57 "initial registration from failnode should fail (should return errs)"
+
+count_osts() {
+ do_facet mgs $LCTL get_param mgs.MGS.live.$FSNAME | grep OST | wc -l
+}
+
+test_59() {
+ start_mgsmds >> /dev/null
+ local C1=$(count_osts)
+ if [ $C1 -eq 0 ]; then
+ start_ost >> /dev/null
+ C1=$(count_osts)
+ fi
+ stopall
+ echo "original ost count: $C1 (expect > 0)"
+ [ $C1 -gt 0 ] || error "No OSTs in $FSNAME log"
+ start_mgsmds -o writeconf >> /dev/null || error "MDT start failed"
+ local C2=$(count_osts)
+ echo "after mdt writeconf count: $C2 (expect 0)"
+ [ $C2 -gt 0 ] && error "MDT writeconf should erase OST logs"
+ echo "OST start without writeconf should fail:"
+ start_ost >> /dev/null && error "OST start without writeconf didn't fail"
+ echo "OST start with writeconf should succeed:"
+ start_ost -o writeconf >> /dev/null || error "OST1 start failed"
+ local C3=$(count_osts)
+ echo "after ost writeconf count: $C3 (expect 1)"
+ [ $C3 -eq 1 ] || error "new OST writeconf should add:"
+ start_ost2 -o writeconf >> /dev/null || error "OST2 start failed"
+ local C4=$(count_osts)
+ echo "after ost2 writeconf count: $C4 (expect 2)"
+ [ $C4 -eq 2 ] || error "OST2 writeconf should add log"
+ stop_ost2 >> /dev/null
+ cleanup_nocli >> /dev/null
+}
+run_test 59 "writeconf mount option"
+
+
+test_58() { # bug 22658
+ [ "$FSTYPE" != "ldiskfs" ] && skip "not supported for $FSTYPE" && return
+ setup
+ mkdir -p $DIR/$tdir
+ createmany -o $DIR/$tdir/$tfile-%d 100
+ # make sure that OSTs do not cancel llog cookies before we unmount the MDS
+#define OBD_FAIL_OBD_LOG_CANCEL_NET 0x601
+ do_facet mds "lctl set_param fail_loc=0x601"
+ unlinkmany $DIR/$tdir/$tfile-%d 100
+ stop mds
+ local MNTDIR=$(facet_mntpt mds)
+ # remove all files from the OBJECTS dir
+ do_facet mds "mount -t ldiskfs $MDSDEV $MNTDIR"
+ do_facet mds "find $MNTDIR/OBJECTS -type f -delete"
+ do_facet mds "umount $MNTDIR"
+ # restart MDS with missing llog files
+ start_mds
+ do_facet mds "lctl set_param fail_loc=0"
+ reformat
+}
+run_test 58 "missing llog files must not prevent MDT from mounting"
+
+if ! combined_mgs_mds ; then
+ stop mgs
+fi
cleanup_gss
equals_msg `basename $0`: test complete
[ -f "$TESTSUITELOG" ] && cat $TESTSUITELOG && grep -q FAIL $TESTSUITELOG && exit 1 || true